Moog EXPF5C12-1 Instruções de Operação Página 1

Moog Inc. Sensor and Surveillance Systems3650 Woodhead Drive, Northbrook, IL. USA 60062 +1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com© 2013,

The micro SD card slot is found at the front of the camera, just under the camera on the lower board. • Inserte la tarjeta SD.• Insérez la carte SD

When pressurizing unit be sure to set the gauge or regulator slightly above the housing pressure target of 5-7psi (0.35-0.5bar).• Al presurizar la

Depress the ll valve. Drain all air from the housing and repeat 3 times to remove all moisture.• Presione la válvula del terraplén. Salga todo el

Replacement Parts ListEXO Fixed HD CameraFRONT BODY ASSEMBLY with WINDOW includedRP40-EXFF01 (PRESSURIZED)RP40-EXFF02 (VANDAL RESISTANT)WINDOWRP30-VL4

TABLE OF CONTENTSSoftware SectionsMoog Discovery Tool ... ...

SOFTWARE SETUP1.0.0 Moog Discovery Tool By factory default, the Moog EXO Camera is congured in DHCP. If you are not using a DHCP server it will au

To congure the Unicast Discovery, add one or more IP address ranges. The Unicast Discovery tries to reach a device at a specic IP address in the con

Assign IP Address(es)Once the IP information is set, the Silverlight web application served by the EXO Camera can be launched from the MDT or directly

2.0.0 Using the Moog EXO Web ApplicationApplicationWhen entering the Web Application, the following window will be displayed. You will be asked a user

Upon successfully logging into the web interface, a welcome screen will be displayed. The welcome screen shows general device health status as well as

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONSUNPACKINGSERVICE1 Read these instructions.2 Keep these instructions. 3 Heed all warnings 4 Follow

2.2.0 System CongurationConguration / SystemUnder the Conguration section, select the System tab to perform the following operations:• View product

2.2.1 Conguration / Date Time2.2.2 Conguration / NetworkUnder the Conguration section, select the Date Time tab to perform the following operations

2.2.3 Conguration / Network / DHCPUnder the Conguration section, select the Network tab to perform the following operations:• Set the camera’s IP pa

2.2.7 Conguration / Network / SNMP Conguration2.2.8 Conguration / Network / RTSP Conguration2.2.6 Conguration / Network / API- Boujour NOTE: •To

2.3.0 Conguration / Video In 2.3.1 Conguration / Video In / Video Input Under the Conguration section, select the Video In tab to perform the follo

Congure video compression parameters for any of the three available codec instances (Primary H.264, Secondary H.264 and MJPEG). Most VMS software sol

2.3.4 Conguration / Video In / Point to Point •Congure point to point video connections (up to three) for creating persistent video streams from the

2.3.6 Conguration / Video In / Motion DetectionSelect from 1 of 4 available regions: • With mouse click on region position box. • Bring mouse pointer

2.3.7 Conguration / Video In / Privacy Zones Privacy Zones are used to block out video in areas view is not permitted or desired. To add a Privacy Zo

2.3.8 Conguration / Audio InUnder the Conguration section, select the Audio In tab to perform the following operations:• Congure audio input compre

Product Warranty RegistrationRegister Your Products Onlinewww.moogS3.com/technical-support/product-registrationMoog values your patronage. We are sole

2.3.9 Conguration / Audio OutUnder the Conguration section, select the Audio Out tab to perform the following operations:• Congure audio output par

2.4.0 Conguration / Recording

Note: Recording Menu will NOT be visible unless activated; see 2.20 System conguration. • Grooming mode; Select method to remove les from full SD ca

2.4.1 Conguration / User Accounts Under the Conguration section, select the User Accounts tab to perform the following operations:• Select the web i

3.0.0 MaintenanceThis section describes how to update your Moog EXO Cameras to newer rmware versions from the web application.1. To nd the latest 

4.0.0 Live ViewerUse Live View for:• Live Camera View • Start and Stop Recording• Camera Control • Setting Presets • Adjust View Scale To enable live

4.1.0 Live Viewer Pan / Tilt and Presets• Speed Control: To increase speed, slide control knob to the right.• Lens Funtion: Use +/- buttons to update

5.0.0 RecordingTo activate recording mode you must go to Conguration / System / Use Recorder Mode. Click “Use Recorder Mode” checkbox. This will act

6.0.0 Performing Batch Firmware UpdateThis section describes how to perform a batch update of multiple Moog EXO Camera devices to newer rmware versi

To start a rmware update session, choose the “.iof” le corresponding to the new rmware by clicking to the “Select File …” button. Once selected, c

Limited Warranty for Moog ProductsMoog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defec

If closed, the progress of the current session can be followed by reopening the “Firmware Update Session” window by clicking the button from the

The Fixed EXO HD Camera System is designed to accept (3) different power inputs. They are:1). PoE - (Factory Ready - EX*F5C-1 models)2). 24 Volt AC

Suggested Hardware for the Mounting Holes: (4) 5/16” - 18 (or M8 for metric) x minimum 1 ¼” Hex Head Bolt • (4) 5/16” Flat Washer • (4) 5/16”

If running wire through a conduit to the housing mount, rst install appropriate ttings to the mount base. • Si se ejecuta a través de un cable de c

Crimp the connectors as needed. Then use cable ties on the nipples to secure, leave an extra 2” of cable.• Crimp los conectores según sea necesario.

Make all nal connections in the rear cavity. To do so, rotate the rear cover by slightly loosing the screw marked (A) and completely loosing the sc